Alinco DR-138  Manuale Utente

A3.130921ALINCO, INC.Yodoyabashi Dai-bldg 13F4-4-9 Koraibashi, Chuo-ku, Osaka 541-0043 JapanPhone: +81-6-7636-2362 Fax: +81-6-6208-3802http://www.ali

21. Install the mounting bracket in the vehicle using the supplied self-tapping screws (4pcs) and at washers (4pcs).2. Position the transceiver,

32RedBlackExt. Power jackDC power cableInitial InstallationDC Power Cable ConnectionMobile OperationThe vehicle battery must have a nominal rat

42Initial InstallationBefore connecting the DC power to the transceiver, be sure to switch the transceiver and the DC power supply OFF.Do not plug t

52GroundErrorInitial Installation External SpeakerIf you plan to use an external speaker, choose a speaker with an impedance of 8Ω. The external

62Microphone connectorMicrophone [EMS-74]Antenna External speakerInitial Installation MicrophoneFor voice communications, connect a provided mic

73NO. KEY FUNCTION1PWR(Power) Power on/Off2VOL Adjust Volume Key3SQL Knob Adjust Squelch level4Main DialChange frequency, memory channel and scan d

8321NO. KEY FUNCTION1Ext. Power JackTerminal for connecting optional cable for use with ignition key On/Off function.2Ext.Speaker TerminalTerminal fo

93NO. KEY FUNCTION1UP Increase frequency, channel number or setting value.2DOWN Decrease frequency, channel number or setting value.3PTT Push-To-Talk

104According to practical application,you can set the radio works as VFO Transceiver mode or Channel mode. 1. 

11In standby, press key or Microphone's key until appear , this indicates current frequency in Memory mode. Repeat above operatio

DR-138DR-438Instruction ManualVHF FM Mobile TransceiverUHF FM Mobile TransceiverThank you for purchasing your new Alinco transceiver. Please read th

12Basic Operations Transmitting Tone BURST TONETransmitting OPTIONAL SIGNALING Press and hold [PTT] key, then press Microphone key to transmit curre

136KEY OPERATIONSFrequency/MEMORY ScanMEMORY Scan(channel scan)CTCSS/DCS Encode and Decode setupScans all VFO frequencies in regard to the preset tuni

146KEY OPERATIONSUP / DOWN keys) to enter the setting and return to original status. The T/SQ/DCS icon will remain on the display to show the current

15Press1. key until LCD displays icon, then press key until LCD displays icon. Now keypad lockout function is valid.After editing, press PTT

16Press 2. / key to choose No.01 menu, LCD displays "STP--125".Turn 3. Main Dial to select the desired frequency channel step.Available s

177Sending 5-Tone CallTurn Main Dial to select the desired 5-TONE group, Press [3. PTT] to transmit selected group. Total:100groups, 00-99, Default:00

187If LCD displays "CTC",it indicates you can hear the calling from caller when receive a matching carrier and CTCSS/DCS signalin

197Busy Channel LockoutBCLO is to disable transmitting while RX signal is received. Once the channel is busy and you press PTT, the radio will beep

207By Talk Around function, you can directly communicate with other radios in your group in case the repeater is not activated or when you are out of

21beep soundThe beep provides conrmation of entry, error status or malfunctions of the radio. You can enable or disable beep sounds.Press and hold 1.

IntroductionThank you very much for purchasing this excellent Alinco transceiver. Our products are ranked among the finest in the world. This radio ha

228Display iiiumination color settingThis is to select the display illumination color.Press and hold 1. / key for over 2 seconds to enter setting men

238PIN Setup(Useless if PIN is not assigned)Enable this function, you have to insert a matching PIN to enter into normal status when radio is turn

24You can operate the transceiver by keypad or input desired frequency or channel through the EMS-74 microphone. Keypad operations may be blocked fo

259Reverse TX/RXTX frequency turns to RX frequency & RX frequency changes to TX frequency. The signaling will also be reversed if CTCSS/DC

269Talk Around By Talk Around function, you can directly communicate with other radios in your group in case the repeater is not activated or when you

2710Steering-wheel etc.[UX1260]DC power cableBatteryOptional alarm cable [UX1259]Anti-theft Alarm Optional extention cable (if necessary)A loud

2811This feature clones the programmed data and parameters in the master unit to slave units. Use commonly available audio-cable with 3.5mm stereo-min

2912DR-138 DCS encode and decode-VFO frequency 155.000MHz DCS code 023NMemory channel 0-199 -Output power HIOffset direction- Key-

3013Specications are subject to change without notice due to advancements in technology.GeneralFrequency Range VHF: 136-174MHz Number of Channels20

31GeneralFrequency Range UHF: 400-470MHz Number of Channels200 channels Channel Spacing25KHz (Wide Band)20KHz (Middle Band)12.5KHz (Narrow band)Channe

SAFETY TRAINING INFORMATIONWARNING: This radio generates RF electromagnetic energy during transmission. This radio is designed for and classified as

321467.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.169.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.671.9 85.4 100.0 118.8 141.3 162.2

3315Appendix320 321 322 323 324 325 326 327330 331 332 333 334 335 336 337340 341 342 343 344 345 346 347350 351 352 353 354 355 356 357360 361 362 36

FOR CLASS B UNINTENTIONAL RADIATORS:This equipment has been tested and found to comply with the limits for a Class B digital device, pu

About transceiver  Environment and condition of use Do not use the product in proximity to a TV or a radio. It may cause inter

CONTENTSSupplied Accessories/Optional Accessories ...1Supplied Accessories ...

CONTENTSBusy Channel Lockout ...... 19Editing Channel NAME ...

11Supplied AccessoriesSupplied AccessoriesCarefully unpack to make sure the following items are found in the package in addition to this manual: Trans